Troubleshooting LIVE-to-VOD recordings

Edited

Overview

This article explains common reasons why LIVE-to-VOD recordings may not appear, may appear as multiple recording files, or may be damaged or out of sync after a Live Event.

LIVE-to-VOD recording captures the stream received by the Media Cloud. If the original live stream has encoder issues, connection interruptions, audio/video sync issues, or other signal problems, those issues may also affect the recording.


When to troubleshoot LIVE-to-VOD recordings

Use this article if you expected a LIVE-to-VOD recording after a Live Event, but the recording:

  • Does not appear in Live Recordings

  • Appears later than expected

  • Appears as multiple recording files

  • Is damaged, incomplete, or out of sync

  • Contains unexpected interruptions or missing portions of the Live Event

For general information about how LIVE-to-VOD recording works, see Understanding LIVE-to-VOD recording.


How it works

LIVE-to-VOD recordings are created from the stream received by the Media Cloud.

The recording starts when the encoder connects and begins sending the stream to the Live Events Channel. It does not start automatically based on the scheduled Live Event start time. The recording stops when the encoder disconnects and stops sending the stream.

If the encoder disconnects during a Live Event, the recording may stop. If the encoder reconnects, a new recording file may be created. This can cause one Live Event to appear as multiple recordings.

Recordings may also be affected by the quality and stability of the original stream. Issues such as network instability, encoder interruptions, incorrect encoder settings, short test streams, or audio/video sync problems may appear in the recording because the recording reflects the stream that was received.


Troubleshooting steps

If your LIVE-to-VOD recording is not showing up

Step 1

Confirm that LIVE-to-VOD recording was enabled for the Live Events Channel before the event started.

LIVE-to-VOD recording must be enabled before the stream is recorded. If the feature was not enabled for the Channel during the Live Event, a recording may not be available.

For setup instructions, see How to enable LIVE-to-VOD recording.

Step 2

Confirm that your encoder has stopped sending the stream.

The recording is not finalized until the encoder disconnects and stops sending the stream to the Media Cloud.

Step 3

Allow time for the recording to process.

LIVE-to-VOD recordings are typically available within 30–60 minutes after the encoder has stopped sending the stream. Processing time may vary depending on the length and bitrate of the recording.

Step 4

Confirm that you are checking MEDIA → Live Recordings.

LIVE-to-VOD recordings are listed under Live Recordings after they become available.

For more information about finding and managing available recordings, see How to manage LIVE-to-VOD recordings.

Step 5

If your account uses Multi-Bitrate Streaming, confirm that your encoder is sending the stream to the High Stream Key for the Live Events Channel.

LIVE-to-VOD uses the high-quality stream to create the recording. If the encoder is not sending a stream to the High Stream Key, the Live Event will not be recorded.

For more information, see Understanding multi-bitrate live streaming.

Step 6

Confirm that the stream did not end too quickly after it started.

Very short streams may not create a usable recording. If you are testing LIVE-to-VOD recording, allow the stream to run for at least 120 seconds before stopping the encoder.

If your LIVE-to-VOD recording is damaged or out of sync

Step 1

Review the original stream quality.

LIVE-to-VOD recording captures the stream received by the Media Cloud. If the original stream had glitches, dropped frames, audio/video sync issues, unstable bitrate, or encoder errors, those issues may also appear in the recording.

Step 2

Review your encoder settings.

Incorrect or unsupported encoder settings can affect both the live stream and the recording. Make sure your encoder is using the recommended live encoder settings.

For recommended settings, see Recommended encoder settings for live streaming.

Step 3

Check for encoder disconnects or rapid reconnects.

Rapid disconnects and reconnects can affect the recorded file. If the encoder disconnects during a Live Event, allow a short cooldown period before reconnecting.

If possible, wait approximately 90 seconds before reconnecting the encoder. This allows the previous recording session to close before a new connection is established.

Step 4

Review your network stability and upload bandwidth.

Use a stable wired connection when possible. Your upload bandwidth should be at least twice the combined video and audio bitrate being sent by your encoder.

Network instability, Wi-Fi interference, insufficient upload bandwidth, router or firewall issues, modem problems, and ISP routing can affect both the live stream and the resulting recording.

For additional troubleshooting steps, see Troubleshooting encoder connection and buffering issues.

If one Live Event appears as several recordings

Step 1

Check whether the encoder disconnected during the event.

If the encoder disconnects, the current recording may stop. If the encoder reconnects, a new recording file may be created.

This can cause one Live Event to be saved as multiple recordings.

Step 2

Confirm whether any disconnects were intentional.

Multiple recordings may be expected if your team stopped and restarted the encoder during setup, testing, or the Live Event.

Step 3

Review the encoder and network connection.

Short disconnects may not always be obvious during the Live Event. The encoder may reconnect quickly enough that the interruption is difficult to notice in the control room, but the disconnect can still cause the recording to split into more than one file.

Step 4

If you are streaming multiple events back to back, disconnect the encoder between events.

This closes the current recording session before the next event begins and helps prevent separate events from being captured as one continuous recording.

For more information about LIVE-to-VOD recording start and stop behavior, see Understanding LIVE-to-VOD recording.


If the issue continues

If the recording is still missing, damaged, incomplete, or out of sync after completing the troubleshooting steps above, contact Customer Support.

When contacting Customer Support, include:

  • The Live Events Channel name

  • The date and approximate time of the Live Event

  • The encoder or streaming software used

  • Whether the live stream itself experienced interruptions or quality issues

  • A description of the issue with the recording

This information can help Customer Support review the issue more efficiently.


FAQs

Why is my LIVE-to-VOD recording not showing up?

A LIVE-to-VOD recording may not appear if LIVE-to-VOD recording was not enabled for the Live Events Channel, the encoder is still sending the stream, the recording is still processing, the stream was not sent to the High Stream Key in a Multi-Bitrate Streaming setup, or the stream ended too quickly after it started.


How long does it take for a LIVE-to-VOD recording to appear?

LIVE-to-VOD recordings are typically available within 30–60 minutes after the encoder has stopped sending the stream.

Processing time may vary depending on the length and bitrate of the recording.


Why is my LIVE-to-VOD recording damaged or out of sync?

The recording may be damaged or out of sync if the original stream had encoder issues, network interruptions, dropped frames, audio/video sync issues, incorrect encoder settings, or rapid disconnects and reconnects.

LIVE-to-VOD recording captures the stream received by the Media Cloud.


Why did one Live Event create multiple recordings?

One Live Event may create multiple recordings if the encoder disconnected and reconnected during the stream.

When the encoder disconnects, the recording may stop. When the encoder reconnects, a new recording file may be created.


Can very short test streams cause recording issues?

Yes. Very short streams may not create a usable recording.

If you are testing LIVE-to-VOD recording, allow the stream to run for at least 120 seconds before stopping the encoder.


Should I reconnect my encoder immediately after a disconnect?

If your encoder disconnects during a Live Event, reconnect as needed to restore the live stream.

If possible, wait approximately 90 seconds before reconnecting the encoder. This allows the previous recording session to close before a new connection is established.


Can long Live Events affect LIVE-to-VOD recordings?

Yes. Longer Live Events have a greater chance of interruptions, glitches, or connection issues. Those issues can affect the recorded file or cause the recording to be split into multiple files.

For more information about recommended recording duration, see Understanding LIVE-to-VOD recording.


Can Customer Support repair a damaged LIVE-to-VOD recording?

LIVE-to-VOD recordings reflect the stream that was received by the Media Cloud. If the original stream included glitches, interruptions, missing audio, sync issues, or other signal problems, those issues may also be present in the recording.

If the recording is damaged or unusable, check whether a local backup recording is available.

You can also contact Customer Support so our team can review the recording and help determine what may have caused the issue. While some recording issues may not be repairable, Customer Support can help confirm whether the issue appears to be related to the original stream, encoder settings, network interruptions, or another factor.


Pricing

LIVE-to-VOD recording is available on POWER packages and up.

If you don't have access to this feature, you can upgrade to one of our latest plans or contact your account manager.


Additional related resources

Was this article helpful?

Sorry about that! Care to tell us more?

Thanks for the feedback!

There was an issue submitting your feedback
Please check your connection and try again.